Cold SAW model h90
350 mm ( 14" ) Saw Blade
| H90 Cutting Range | 90° | 45° | 60° |
|---|---|---|---|
| round tube ⦿ | 115 mm - 4.5" | 110 mm - 4.3" | 100 mm - 3.9" |
| square tube ▣ | 105 mm - 4.1" | 100 mm - 3.9" | 95 mm - 3.7" |
| section tube ▭ | 108 mm x 70 mm - 7.1" x 2.8" | 160 mm x 70 mm - 6.3" x 2.8" | 120 mm x 70 mm - 4" x 2.8" |
| Channel-girder | 150 mm x 80 mm - 6" x 3.2" | 140 mm x 80 mm - 5.5" x 3.2" | 100 mm x 65 mm - 4" x 2.6" |
| solid mild steel ⬤ | 60 mm - 2.5" | 60 mm - 2.5" | 60 mm - 2.5" |
HABERLE Model H 90: HSS Saw Blade (14") 350x40mm/ Compound angel cuts, notching, angle cuts, slitting, for tubes, sections or channels of steel, stainless steel and nonferrous metals. Saw head tilts 0° - 90°
2-PIECE SAFETY GUARD of aluminum covers the whole saw blade in rest position. Multiple latch linkage with quick release knob for easy and fast saw blade replacement without removing the guards.
PRECISION WORM & WHEEL DRIVE with hardened and ground worm shaft, special bronze worm wheel and a main spindle of 70 mm (2.7") dia. running in oil. Elastic coupling between motor and gears.
TILTING SAW HEAD allows vertical mitering 0º-90º to the right side. The vise in place, it allows compound angles with tilted head 0º- 45º' and mitered vise 0º'- 60º according to the 1º- graduations. Quick adjustment by clamp levers without tools. Safe handling of the rigid moving head. Large tilting block for exact angle cuts. Double yoke pivot, adjustable.
MITERING & MOVING VISE allows horizontal angle cuts 0º- 60º. Positive lock by spring-loaded pin in straight and 45º position. To meet the total cutting range of the saw blade, the mitering vise can be moved backwards. For notching and slitting cuts, the vise can be removed and placed to the left side.
NOTCHING CUTS WITH 90° TILTED HEAD: The vise placed to the left side, the saw head can be tilted vertical up to 90º for notching cuts into channels and T-size profiles. The spring-loaded saw head movement enables exact cuts.
SLITTING CUTS IN DOOR FRAMES: The vise replaced to the left side, it allows also parallel slits by the positive 90º locking. All adjustments are done by clamp levers without tools.
MATERIAL SUPPORT BLOCK
on the left side of the table, supports the cut-off piece for safe straight and miter cuts. The block can be moved when the tilted head makes it necessary and removed to replace the vise to the left side.
SPECIAL APPLICATIONS Total altitude between table and saw blade is 210 mm (8.3") and allows various clamping
devices for many purposes, usually done on a milling machine, like slitting of bolts etc.
FREE ADJUSTABLE TURN TABLE allows always the same direction of the material feed-in. After mitering adjustment, turn the whole machine into position.
SAW BLADE SIZE H.S.S. 350x40 mm (14"); 325x40 mm (13"); 300x40 mm (12"). Two drive holes 11 mm on circle 64 mm dia. Segmental blades are not recommended, they can over stress the machine. Use the right rake angle: 16º-18º for steel and stainless steel, 22º-25º for soft aluminum alloys.
SAW BLADE SPEED AND MOTOR POWER
60 Hz: 27/54 RPM, 1.2/2.4 kW (1.7/3.3 HP)
WATER COOLANT SYSTEM
with large coolant tank and chip container in the base. Reliable diaphragm coolant pump for water emulsions. Optional: Low-consumption cutting oil lubricating system or air operated oil spray system available.
ELECTRICAL EQUIPMENT 3-phase (220 V, 460 V, or 575 V), 2 speed motor. Main switch with motor protection.
AIR OPERATED VISE SYSTEM with vise cylinder 160 mm (6.3") dia., automatic stroke 8 mm (0.3"), air pilot valve, front regulator and filter-lubricator. Clamping is actuated when the saw head is moved from rest position by operating handle. necessary air supply: 6 bar (90 PSI).
DIMENSIONS AND WEIGHT (W x L x H) 700x1200x1900 mm (28"x47”x75”), approx. 320 kg.
STANDARD EQUIPMENT Grease gun, wrenches, operating manual, quick-action mechanical vise, coolant system, 24 Volt stop & go switch, 1 H.S.S. saw blade, coolant fluid
OPTIONAL EQUIPMENT Air vise system, length stop, oil lubricant systems, saw blade, coolant fluid, oil spray system.